Descrição
Informações sobre o produto
Modelos relacionados e alternativos
Other ratings in the MPS series, and the Emparro unit that distributors list as its successor.
MPS series, other ratings:
- MPS10-230/24 — 10 A version, art. 85055
- MPS10-110/24 — 10 A, for 110 V AC supplies
Successor and mounting accessory:
- 85440 — Emparro 5-100-240/24, 24-28 V DC 5 A
- 89500 — screw-mounting plate for DIN-rail units
Potensi supplies the Murrelektronik power supply MPS5-230/24 and the Murrelektronik 24 V DC power supply range used in lift control cabinets. The models above are only a part of what we can supply. We stock and source a much wider range of related and alternative models. If your model number is not listed here, please send us the model number or a photo of the original part, and we will confirm availability and the correct match for you.
Porquê escolher a Potensi?
- Cobertura de mercado do 99%: Podemos fornecer cerca de 99% de peças sobressalentes para elevadores disponíveis no mercado.
- Garantia de Qualidade Autêntica: Fornecemos componentes para elevadores originais e fiáveis.
- Apoio à identificação por peritos: Envie-nos o número do modelo ou fotografias do produto e poderemos ajudá-lo a identificar a peça correta.
- Envio internacional: Oferecemos um serviço de entrega internacional rápido e fiável para projetos de manutenção de elevadores.
Perguntas frequentes
Q1: What does this unit do in a lift cabinet?
R: It converts the mains supply into the 24 V DC rail that the control boards, relays and door operator run on. Output is 24 V DC at 5 A, 120 W, delivered as SELV, with short-circuit and overload protection built in. It is a power supply, not a controller: it carries no lift parameters and holds no software.
Q2: Is it 5 A or 6 A?
R: Both figures come from the same data sheet, at different temperatures: 6 A up to 40 °C and 5 A up to 60 °C. Plan the load on the 5 A figure unless the cabinet stays genuinely cool. Loads close to the limit on a warm shaft can trip the unit even though nothing is faulty.
Q3: Can I put two in parallel for more current?
R: No. The data sheet allows serial connection but expressly rules out parallel operation. Two units on one rail will not share the load evenly and one will carry the work. If you need more current, go to the 10 A version rather than adding a second 5 A unit.
Q4: Is 85053 still obtainable, and what replaces it?
R: Distributor records list it as replaced by 85440, the Emparro 5-100-240/24, which gives 24-28 V DC at 5 A. The two are not identical: the Emparro output is adjustable and the housing is a different width, so check the mounting space. Tell us which of the two your cabinet takes and we will quote that one.
Q5: Does it only work on 230 V?
R: No. The input range is 90-265 V AC at 50/60 Hz, so 110 V, 120 V, 230 V and 240 V supplies all fall inside it. Input current is 1.9 A at 115 V and 0.95 A at 230 V, and the unit bridges mains dips of about 10 ms at 115 V and 80 ms at 230 V. That wide range is why one article number appears in cabinets built for different markets.
Q6: What should I send with the order?
R: A photo of the old unit with the label readable, showing the article number and the output rating. The mains voltage at the site, and the load in amps that the 24 V rail actually carries. Whether the cabinet has room for a wider housing, in case the successor is the one offered.

