The PBCM-V3 is the base board of the Orona ARCA 3 control cabinet, part number 5124501. It is the board the CPU works through: the safety chain, door contacts, drive fault input and landing remote line pass through it. In ARCA and Basic ARCA panels it also carries the status LEDs used for fault finding without a test tool. The same number is quoted as PBCM-V2 and PBCM-V3, so please send a photo of the marking before ordering.
卸売業者であろうと、メンテナンス会社であろうと、POTENSIが必要なすべての部品のためのONE-STOP-SHOPであることがお分かりいただけるでしょう。
POTENSIでは、私たちの焦点は、中国のエレベーター業界で21年の経験を持つ、簡単にすべてのブランドのエレベーターやクライアントのすべての種類へのアクセスを支援することです。
POTENSIの使命は、最高品質のエレベーター部品と卓越したサービスにより、お客様の成功を支援し、世界中の建物の安全性を高めることです。
納品スピードはポテンシの強みですが、他社との違いはマルチブランドの提供です。POTENSIからの購入は、200K以上のマルチブランドパーツでとても簡単です。
ウェブショップは24時間年中無休で営業しております。一度 登録済み 会員になると、様々な特典が受けられ、必要なパーツをコードで検索でき、セールススペシャリストによるVIPサービスを受けることができます。
高品質を保証するために、POTENSIは、元の機器メーカーまたはその直接サプライヤーによってのみ部品を提供します。POTENSIと協力することで、顧客と対峙する際に成功の保険を得ることができます。
PBCM base boards by ARCA generation:
Orona ARCA boards often requested together:
Potensi supplies the Orona elevator control board PBCM-V3 5124501, the Orona ARCA 3 base board and other Orona elevator PCB boards. The models above are only a part of what we can supply. We stock and source a much wider range of related and alternative models. If your model number is not listed here, please send us the model number or a photo of the original part, and we will confirm availability and the correct match for you.
Q1: What does the PBCM board do in an Orona lift?
A: It is the base board of the control cabinet, not the CPU board. The cabinet inputs and outputs run through it: the safety chain, the door contacts, the drive fault signal and the landing remote line. The CPU board carries the software and the parameters; the PBCM is the board it works through.
Q2: Is 5124501 the same as 5124501-1, and is it V2 or V3?
A: 5124501 is the Orona part number for the ARCA 3 base board, and 5124501-1 is the same number with a revision index. The market quotes this number both as PBCM-V2 and as PBCM-V3, so the version is not settled by the number alone. Please photograph the marking on your old board; we check the version against it before shipping.
Q3: Can I fit the ARCA 2 or ARCA 1 board instead?
A: No, each ARCA generation has its own base board. The ARCA 1 board is 5124030 and the ARCA 2 board is 5124336, with a second ARCA 2 board quoted as 5124423. They look similar but belong to different panels, so the generation has to be confirmed from the cabinet, not from the board shape.
Q4: How can I find the fault without the Orona test tool?
A: In the ARCA and Basic ARCA panels the PBCM carries the status LEDs, and they can be read without any tool. The red LED shows that 220 V reaches the manoeuvre panel, D69 and D70 show that the board is powered, and P32, P35 and P36 show the safety chain and the door contacts. AV on means no blocking fault is stored; if the lift is standing with FS and AV lit, it has entered a special mode such as inspection, ERO or fire service.
Q5: How do I tell whether a landing remote station is causing the fault?
A: In the ARCA and Basic ARCA panels the landing remote line is plug J10 on the PBCM. Unplug J10 and put the lift on normal; if it starts taking car calls, the fault is in the landing circuit. Then reconnect the stations one by one until the lift stops again, which identifies the faulty board.
Q6: Which Orona systems use this base board, and what else fits with it?
A: It is the base board of the ARCA 3 control system used on Orona lifts of that generation. In the same cabinet you will normally find the CPU board, and on the car roof the PDCC car distribution board. Please send the cabinet photo and the board label, and we will confirm the generation and the matching boards for you.
初回注文時に10%を割引。
プロモーション商品の最新情報をお届けします。
年中無休のセールススペシャリストによるVIPサービスをご利用ください。
クレジット決済をご利用いただけます。
