Festo part 536366 is the ADN-80-25-I-P-A compact pneumatic cylinder, an 80 mm bore cylinder with a 25 mm stroke to ISO 21287, made in Germany. Double-acting with a magnetic piston, it pushes 3016 N at 6 bar and pulls 2827 N from a body short enough to sit inside a door frame. The rod end is an internal M12 thread, cushioning is elastic at both ends, and the ports are G1/8. It runs on 0.6 to 10 bar filtered air, down to -20 °C.
卸売業者であろうと、メンテナンス会社であろうと、POTENSIが必要なすべての部品のためのONE-STOP-SHOPであることがお分かりいただけるでしょう。
POTENSIでは、私たちの焦点は、中国のエレベーター業界で21年の経験を持つ、簡単にすべてのブランドのエレベーターやクライアントのすべての種類へのアクセスを支援することです。
POTENSIの使命は、最高品質のエレベーター部品と卓越したサービスにより、お客様の成功を支援し、世界中の建物の安全性を高めることです。
納品スピードはポテンシの強みですが、他社との違いはマルチブランドの提供です。POTENSIからの購入は、200K以上のマルチブランドパーツでとても簡単です。
ウェブショップは24時間年中無休で営業しております。一度 登録済み 会員になると、様々な特典が受けられ、必要なパーツをコードで検索でき、セールススペシャリストによるVIPサービスを受けることができます。
高品質を保証するために、POTENSIは、元の機器メーカーまたはその直接サプライヤーによってのみ部品を提供します。POTENSIと協力することで、顧客と対峙する際に成功の保険を得ることができます。
Other versions of the same cylinder, and other makes of 80 x 25 ISO 21287.
Festo ADN variants:
80 x 25 ISO 21287 equivalents:
Potensi supplies the Festo compact cylinder ADN-80-25-I-P-A 536366, the Festo pneumatic cylinder in other ADN sizes, and the ISO 21287 crossover cylinders. The models above are only a part of what we can supply. We stock and source a much wider range of related and alternative models. If your model number is not listed here, please send us the model number or a photo of the original part, and we will confirm availability and the correct match for you.
Q1: What does the code ADN-80-25-I-P-A tell me?
A: Read it as series, bore, stroke, rod end, cushioning and sensing. ADN is the compact cylinder series to ISO 21287, 80 is the 80 mm piston diameter and 25 is the 25 mm stroke. The I marks the internal piston rod thread, the P the elastic cushioning rings at both ends, and the final A the version that takes proximity sensors, which Festo confirms in the datasheet.
Q2: How much force does it give?
A: Festo rates 3016 N advancing and 2827 N retracting at 6 bar, theoretical figures at the piston. The working range is 0.6 to 10 bar, so at 4 bar you get roughly two thirds of that, and the barrel is rated for the full 10 bar. Size the load from the pressure you actually run, not from the maximum.
Q3: What thread, ports and mounting does it have?
A: The piston rod ends in an M12 female thread, so a rod clevis or a rod eye screws straight in. The air ports are G1/8, and the body mounts on through-holes, on internal threads, or with Festo mounting accessories, in any position. Moving mass is 347 g and the complete cylinder weighs about 1.19 kg.
Q4: What is the difference between I-P-A and A-P-A?
A: The letter before the P is the rod end. I is the internal thread, M12 on this bore, and A is the male thread, which Festo makes M16x1.5 on the 80 mm bore. Both are 80 mm bore, 25 mm stroke, double-acting cylinders with elastic cushioning, and both take proximity sensors. Order by the full code, because the thread decides which rod accessory fits.
Q5: Can I use an SMC or Norgren cylinder of the same size?
A: Mechanically the 80 x 25 ISO 21287 cylinders share the mounting and the bore and stroke, which is why the crossover numbers are listed above. They are not identical: the rod thread, the cushioning type, the port size and the sensing groove can differ between makes. If you are replacing one brand with another, send us the old part and we confirm the thread and the ports before you order.
Q6: How do I check it fits my installation?
A: Read the label on the old cylinder: the full code gives bore, stroke, rod end and cushioning in one line, and the five-digit number confirms it. Measure the stroke if the label is gone, and check the rod thread with a thread gauge or a known nut. Send us a photo of the label and the mounting and we will confirm the match.
初回注文時に10%を割引。
プロモーション商品の最新情報をお届けします。
年中無休のセールススペシャリストによるVIPサービスをご利用ください。
クレジット決済をご利用いただけます。
