Elevator Connection Board KBK12-13 1003527 for Arkel

Описание

Информация о продукте

Схожие и альтернативные модели

Other Arkel connection boards, and the ARCODE panel boards that are replaced alongside them.

Arkel connection boards:

• KBK-10 & KBK-11 — ARCODE panel set, 1002430
• KBK 2 — connection board
• KXCBA — CANbus terminal board

Arkel ARCODE panel boards:

• ETM — 1002286
• IBC-S — 1003451
• DBR — 1002346
• ENCA — 1002919
• ENCI — 1002920
• SP-16 — 1002455

Potensi supplies the Arkel elevator connection board KBK12-13, the Arkel elevator terminal board and the Arkel PCB board range for ARCODE panels. The models above are only a part of what we can supply. We stock and source a much wider range of related and alternative models. If your model number is not listed here, please send us the model number or a photo of the original part, and we will confirm availability and the correct match for you.

Почему стоит выбрать Potensi?

• Охват рынка 99%: Мы можем поставить на рынок запасные части для лифтов объемом почти 99%.
• Надежное обеспечение качества: Мы поставляем оригинальные и надежные комплектующие для лифтов.
• Поддержка экспертной идентификации: Пришлите нам номер модели или фотографии товара, и мы поможем вам определить нужную запчасть.
• Международная доставка: Мы обеспечиваем быструю и надежную международную доставку для проектов по техническому обслуживанию лифтов.

Часто задаваемые вопросы

Q1: What does the KBK12-13 board do?

A: It is the connection board of the ARCODE controller panel, where the panel’s field wiring is landed. Arkel describes it as the connection card inside the controller panel; it groups the terminal points so the wiring from the shaft, car and machine room meets the controller in one place. It carries no control logic, so it cannot be the cause of a controller that is completely dead.

Q2: Is this one board or two?

A: Arkel lists KBK12 and KBK13 together under a single code, 1003527, and distributors offer it as one article. Send us a photo of the card you are taking out, and we will confirm whether your panel needs the pair or one board.

Q3: Does it replace the older KBK-12 V1.03?

A: Yes. This board is supplied in place of the earlier KBK-12 V1.03 card. The terminal positions still follow the panel drawing, so keep the drawing for the panel you are working on and land the wires as it shows. Tell us the version printed on the old card when you order.

Q4: Is it the same as the KBK-10 & KBK-11 set?

A: No. That is a different connection board set with its own code, 1002430. The ARCODE panel drawing names either one set or the other, and the two are not the same article. Check which designator your drawing carries before ordering.

Q5: What faults point to this board?

A: Because it only carries terminals and links, its failures show up as intermittent or missing signals rather than as a fault code of its own. Typical reports are calls that drop in and out, inspection signals that do not register, and readings that change when the panel door is moved. Tighten and inspect the terminal screws and the plug-in links first, since a loose screw gives exactly the same symptom.

Q6: What should I send before ordering?

A: A photo of the old board, front and back, with the designator and version readable. The page of the panel drawing that shows the connection board. The quantity you need, since panels of different sizes use this board in different numbers.