エレベーター試験用ツール:その概要と分類

目次

Why a lift needs a tool at all

A lift cannot be judged by looking at it. The doors close, the car moves, nothing sounds wrong. The brake may be releasing late. The governor may trip at the wrong speed. A rope may be one journey from failing. None of that is visible from the landing.

Some of it is written down inside the controller. The rest has to be measured.

Elevator testing tools do those two jobs. They read what the controller recorded, and they measure what the controller cannot see. The two jobs are different, and so are the tools.

What a service tool actually is

Most lifts built since the 1990s have a small port in the control cabinet. Plug a service tool into it, and the tool and the controller start a conversation. That port is what most elevator testing tools are built to plug into. The tool asks questions. The controller answers from its own memory.

Think of the diagnostic socket in a car. A mechanic plugs in, reads the stored faults, watches live values, and clears the code once the repair is done. An elevator service tool does the same three things:

  • Read. Stored faults, event history, the state of every input and output.
  • Change. Parameters: speeds, times, floor tables, door behaviour. Some are safety-relevant, which is why access is restricted.
  • Test. Drive the car slowly, run a door cycle, relearn the floors after a rope change.

The tool is not part of the lift. It does not travel with the car. It is a window and a keypad, not a repair. What it shows still has to be interpreted, and what it changes still has to be measured afterwards.

Older lifts without a port are not tested with a service tool. They are tested with meters, gauges and judgement, which is why the other families below exist.

The six families of elevator testing tools

FamilyWhat it answersUsual form
A. Controller service toolsWhat does the controller think is wrong?Handheld or laptop
B. Electrical instrumentsIs the power and wiring sound?Portable meters
C. Safety-part testersDo the safety devices act at the right point?Dedicated rigs
D. Load and balance testingDoes it behave the same with the rated load?Weights or load cells
E. Bus and signal diagnosticsIs the data arriving intact?Analyser, oscilloscope
F. Adapters and licencesCan the tool connect at all?Cables, dongles

The order follows a call-out. The controller is asked first because it is fastest. If it reports nothing, the meter comes out. If the fault only appears under load, family D comes in. No single elevator testing tool covers the whole list.

A. Controller service tools

Four sub-types. All of them read or write the controller’s memory.

Sub-typeWhat it is代表的な用途
A1. Handheld terminalDedicated keypad and screenFault codes, parameters, test runs on a call-out
A2. Laptop softwarePC tool plus cableFull parameter sets, logs, job files
A3. Board-level programmerBench device with adaptersGiving a replacement board its program
A4. Simulator or test boxSignal sourceTesting a controller with no lift around it

A1 is what most people mean by an elevator testing tool. It is fast, and it fits in one hand. It answers the question the passenger is asking: why did it stop?

A2 does the same job with more depth. Parameter sets can be saved, compared and copied between lifts, which is what a modernisation or a board swap needs.

A3 is the one people outside the trade never see. A replacement board arrives without its program. The programmer writes it, on a bench, before the board goes into a shaft.

A4 is a workshop item. It feeds the controller the signals a lift would feed it, so a fault can be reproduced without a building.

What family A cannot tell you. Voltage, insulation resistance, brake force, door closing force. A service tool reporting “no fault” means the controller is content with the inputs it can see. It says nothing about a cable that is about to fail.

B. Electrical instruments

Six sub-types. None of them is built for lifts, yet every elevator testing toolkit ends up holding all six.

Sub-typeMeasuresFinds
B1. MultimeterVoltage, resistance, continuityBroken control circuits, dead coils
B2. Clamp meterCurrent without opening the circuitMotor current, brake coil current
B3. Insulation testerResistance at 500 V or 1000 VDamaged travelling cable, damp windings
B4. Earth and continuity testerBonding resistanceMissing or high-resistance earth
B5. Phase sequence testerRotation orderWrong rotation after a supply change
B6. OscilloscopeWaveform over timeMissing encoder edges, noise on a bus

B3 finds what a multimeter misses. A damaged travelling cable can read perfectly on a low-voltage continuity test. At 500 V it fails.

C. Safety-part testers

Five sub-types. These answer an inspector’s question, not a passenger complaint.

Sub-typeChecks
C1. Governor testerThe speed at which the overspeed governor actually trips
C2. Brake testerRetardation or braking torque under load
C3. Buffer checkStroke and reset of the buffers
C4. Door force gaugeClosing force and kinetic energy
C5. Load cell and calibration setCar weight, overload device trip point

A service tool knows what the controller was told. A governor tester knows what the governor did. Those are different facts, and only one of them is evidence.

D. Load and balance testing

Sub-type方法Used for
D1. Test weightsPhysical weights in the carAcceptance, and jurisdictions that still require them
D2. Electronic Category 5Load cells and a loggerPeriodic testing without moving tonnes of steel
D3. Balance coefficient testCurrent at 40 and 50 percent loadSetting the counterweight correctly

D1 and D2 answer the same question by different routes. D3 is not a test in the legal sense. It is how the machine is set up, so it does not work against itself for ten years.

E. Bus and signal diagnostics

Sub-typeMeasuresUsed when
E1. CAN analyserTraffic, error frames, node presenceA bus fault that moves when the car moves
E2. Cable and termination testerContinuity, shield, terminating resistanceAfter a travelling cable replacement
E3. Encoder signal testerPulse count, phase, missing edgesSpeed feedback faults, levelling drift

Family E is the last resort, and the most decisive. When a fault survives three board swaps, the board was never the problem.

F. Adapters, licences and documentation

Sub-typeCoversその重要性
F1. Cables and convertersPort adapters, USB to serial, optical headsA tool without the right connector cannot connect
F2. Licence and dongleSoftware entitlement per controller familyThe box is cheap; the entitlement is not
F3. Manuals and trainingParameter lists, fault code tablesThe tool shows a code; the document says what it means

F is where budgets go wrong. Buyers compare the price of the box. They forget the licence, the adapter set and the current manual are part of the working system.

Same tool, four ways to use it

FormWorks where制限
HandheldShaft, car top, pitSmall screen, no logging
LaptopMachine room, officeNeeds power and boot time
BenchWorkshopThe board must be out of the lift
In-linePermanently installedA monitoring product rather than a tool

Which family for which symptom

目に見えるものStart withThen
Car stops between floorsA1: read the fault logE3 if the log points at speed feedback
Annual inspection dueC1 and C4B3 on the travelling cable
New installationA2: parametersD3 balance, D1 or D2 proof
Rough ride, no fault codeB6: waveformB3 insulation
Fault returns after a board swapE1: bus trafficE2 cable and termination
Overload device trips earlyC5 load cellD3 balance

Five questions anyone can ask

  1. Which controller families does it cover, and which software version is on each?
  2. Is the licence per device, per site or per year?
  3. Does the price include the adapters for the ports on this lift?
  4. Can the unit be repaired, and by whom?
  5. Does the supplier provide the fault code table, or only the box?

Five rules that hold across all six families

  • A service tool reads and writes the controller. It does not measure the machine.
  • Meters and safety-part testers measure the machine. They do not read the controller.
  • Neither replaces the other, which is why a call-out uses at least two families.
  • The licence, the adapter and the manual are part of the tool, not extras.
  • When a fault survives a board swap, suspect the cable or the bus.

Source note

Families and roles follow current maintenance practice and parts catalogues. Model names such as TH-1, GAA21750AK3 and CPU561 are examples in circulation, not a compatibility list. The Category 5 comparison follows Elevator World, February 2025.

ポテンシロゴ
お客様のプライバシーを尊重し、お客様の情報を共有することはありません。