MNCU-8C is the main board of the TKE elevator inverter, the control board of the drive unit that feeds the hoisting motor, mounted in the drive section, not in the car. Distributors also list it as PWB-PL MNCU-8C, and it is supplied in more than one revision, including Rev 2.0. A failed board takes the drive down, so the lift stops even when the controller is healthy. Match the marking and the revision on the old board before ordering.
卸売業者であろうと、メンテナンス会社であろうと、POTENSIが必要なすべての部品のためのONE-STOP-SHOPであることがお分かりいただけるでしょう。
POTENSIでは、私たちの焦点は、中国のエレベーター業界で21年の経験を持つ、簡単にすべてのブランドのエレベーターやクライアントのすべての種類へのアクセスを支援することです。
POTENSIの使命は、最高品質のエレベーター部品と卓越したサービスにより、お客様の成功を支援し、世界中の建物の安全性を高めることです。
納品スピードはポテンシの強みですが、他社との違いはマルチブランドの提供です。POTENSIからの購入は、200K以上のマルチブランドパーツでとても簡単です。
ウェブショップは24時間年中無休で営業しております。一度 登録済み 会員になると、様々な特典が受けられ、必要なパーツをコードで検索でき、セールススペシャリストによるVIPサービスを受けることができます。
高品質を保証するために、POTENSIは、元の機器メーカーまたはその直接サプライヤーによってのみ部品を提供します。POTENSIと協力することで、顧客と対峙する際に成功の保険を得ることができます。
Other TKE inverter boards, and the control boards that work with the drive.
TKE inverter and drive boards:
TKE control boards:
Potensi supplies the TKE elevator inverter main board MNCU-8C, the TKE elevator drive board and the TKE PCB board range around it. The models above are only a part of what we can supply. We stock and source a much wider range of related and alternative models. If your model number is not listed here, please send us the model number or a photo of the original part, and we will confirm availability and the correct match for you.
Q1: What does the MNCU-8C board do?
A: It is the main board of the inverter, the unit that converts the supply into the voltage and frequency the hoisting motor needs. The board carries the control electronics of that unit, so the drive’s own diagnostics and its output control run through it. It is a drive board, not the lift controller: when it fails the controller is still alive, but the motor gets no drive.
Q2: Is it the same as an MC1 or MC2 board?
A: No. MC1 and MC2 are controller boards, and this one belongs to the inverter section. They are different parts in different places in the cabinet, and one cannot stand in for the other. If you are not sure which section your board comes from, send us a photo of the cabinet with the board in place.
Q3: Does the revision matter?
A: Yes. The board is listed in more than one revision, and Rev 2.0 is the one most distributors carry. A different revision may not behave like the board you are taking out, even where the marking looks the same. Read the revision printed next to the marking and tell us both before ordering.
Q4: Which TKE inverters use this board?
A: The public listings for MNCU-8C do not name the drive families, so we will not guess at them. What identifies it is the marking on the board, the revision, and the drive label in the cabinet. Send us those photos and we will confirm the fit for your installation.
Q5: The drive trips and the lift stops. How do I know the board is at fault?
A: Note the fault code the drive displays first, because it points at the section that failed. Check the supply and the motor connections before the board: a loose power terminal or a motor insulation fault produces the same stop. If the supply and the motor are sound and the code keeps returning, the main board is the next suspect.
Q6: What should I send before ordering?
A: A photo of the old board, front and back, with the marking and the revision readable. A photo of the drive label, and the fault codes the drive has stored. With those three we confirm the board, the revision and the fit before dispatch.
初回注文時に10%を割引。
プロモーション商品の最新情報をお届けします。
年中無休のセールススペシャリストによるVIPサービスをご利用ください。
クレジット決済をご利用いただけます。
