Elevator Main Board MC1 HV2 65100004029 for TKE

الوصف

معلومات عن المنتج

النماذج ذات الصلة والبديلة

Other MC1 numbers, the rest of the MC series, and the TKE boards we ship alongside it.

MC1 and the MC series:

• 6510078680 — MC1 board, another number
• 6500630750 — MC1 board, another number
• MC2 — next board in the series
• MC3 — later board in the series

Other TKE boards:

• 66200009274 — RMB3 HV1 relay board
• 65000007730 — MH4-GT drive board
• 6510053680 — PC MS 2 board
• 6510066680 — MF4 board

Potensi supplies the TKE elevator main board MC1 HV2 65100004029, the TKE elevator control board and the TKE PCB board range around it. The models above are only a part of what we can supply. We stock and source a much wider range of related and alternative models. If your model number is not listed here, please send us the model number or a photo of the original part, and we will confirm availability and the correct match for you.

لماذا تختار بوتنسي؟

• تغطية سوق 99%: يمكننا توفير ما يقارب 99% من قطع غيار المصاعد المتوفرة في السوق.
• ضمان الجودة الأصلي: نحن نوفر قطع غيار مصاعد أصلية وموثوقة.
• الدعم في تحديد الهوية من قبل الخبراء: أرسل إلينا رقم الطراز أو صور المنتج، وسنساعدك في تحديد القطعة المناسبة.
• الشحن الدولي: نحن نقدم خدمة توصيل دولية سريعة وموثوقة لمشاريع صيانة المصاعد.

الأسئلة الشائعة

Q1: What is the MC1 HV2 board?

ج: It is a controller board of the TKE lift control station, and HV2 is its hardware version, the second revision of the board. Distributors describe it in two ways, as the main board and as the interface board, and both are in circulation for this number. It carries the control electronics and handles the signal exchange between the controller and the subsystems connected to it.

Q2: Are 6510078680 and 6500630750 the same board?

ج: They are listed together with 65100004029 under the MC1 board, so they belong to the same family. They are not automatically interchangeable, because the number usually marks a different hardware revision or build. Send us the number printed on your board and we will tell you what we can match it with.

Q3: Does the firmware matter when I replace it?

ج: Yes. MC1 boards are offered with the firmware loaded, which means software is part of what you are buying, not only the PCB. A board with the wrong version will not behave like the old one, even if the hardware number matches. Tell us the software version on the site, or send a photo of the old board’s label, and we will confirm before dispatch.

Q4: Can I use an MC2 or MC3 board instead?

ج: No. MC2 and MC3 are different boards of the same series, and they are not a substitute for an MC1. They differ in hardware and in the way they are programmed, so fitting one changes the controller. Order by the MC number as well as the part number.

Q5: Which TKE controllers take this board?

ج: The public listings for this number do not name the controller families, so we will not guess at them. What identifies the board is the number on the PCB, the MC1 designation and the HV2 marking. Send us photos of the cabinet and the board and we will confirm the fit for your installation.

Q6: What should I send before ordering?

ج: A photo of the old board, front and back, with the number and every connector visible. The cabinet photos, showing the other boards and the labels inside the door. With those three we confirm the number, the hardware version and the firmware before dispatch.